How To Apply Stellmann Non-Slip Clear PRO?

Learn how to apply Stellmann Non-Slip by following the below steps. Ensure you have the appropriate tools and application technique. We recommend thoroughly reviewing our guidelines, Technical Data Sheets and Safety Data Sheets (available at our Resource Page or via info@stellmannn.com.au).

For any urgent questions, please don’t hesitate to call us at 1300 987 095.

How To Apply Stellmann Non-Slip

1. Pre-Application Surface Prep

Thoroughly clean the surface using Stellmann Prep & Maintenance Cleaner, ensuring the removal of all dirt, dust, and unwanted materials.

Use a squeegee to remove contaminated water and wash/rinse the surface until all foaming ceases. Make sure the surface is completely dry before starting the Stellmann application.

Verify that previously applied coatings are firmly bound to the substrate. Remove any loose or flaking paint/coatings thoroughly before application.

Play

2. Stellmann Primer

Stellmann Clear Primer is a single-component primer that is over-coatable in approximately 30 minutes. It is designed to optimise the adhesion of the Stellmann Non-Slip Clear PRO coating to any surface.

  • Stir/shake prior to use and dilute with water on a 1:1 ratio.
  • High suction substrates like concrete may require more primer. Apply two layers to raw timber.
  • Small areas (-15sqm): use a sponge to apply the primer to the surface.
  • Large areas: (15sqsm+): use a flat microfiber mop to evenly apply the primer to the surface.
  • Avoid puddling, skinning and streaks.
  • Cures in approx. 30 min at 21°C and 50% relative humidity; higher temperatures shorten and lower temperatures lengthen these times. Surface is ready for application if dry and slightly tacky.
  • Do not use cleaning agents after applying Stellmann Primer. Over-coat Prime within 8 hours.
How To Apply Stellmann Non-Slip

3. Product Prep

Our 5m2 and 15m2 packs can be mixed at once when product will be immediately used. Start by stirring up Part A, then add Part B and thoroughly mix the two components together with an electrical mixer. Apply within 45 minutes.

Required Tools:

  • Roller holder/handle
  • Electrical precision scale (e.g. digital kitchen scale) and clean mixing cup/pail when mixing in smaller portions.
  • Clean paint tray
  • Clean mixing cup
  • Electric drill
  • Two mixing heads. One to stir up Part A and the second (clean one) to mix Part A and B (Compulsory)

IMPORTANT: It is compulsory to mix Part A and Part B with an electric drill and mixer. Shaking is not sufficient to get a good mixture. Only mix manually for smaller quantities (less than 300 grams Part A).

4. Mixing Smaller Portions

Refer to the table on the left for mixing instructions if you don’t want to use all coating at once.

Mixing Ratio: 5 to 1 by Weight

  • For every 5 grams of Coating A, add 1 gram of Hardener B.
  • Place mixing cup on the electrical precision scale, turn on and add desired amount of Part A.
  • Add Part B to mixing cup in the right ratio.
  • Stir mixture thoroughly with a clean electric mixer.
Play

5. Applying Stellmann Non-Slip Clear

Apply Stellmann Non-Slip Clear PRO with the supplied roller.

  • Pour mixture of Part A and Hardener B in a clean paint tray.
  • Allow roller to absorb sufficient material. Do not roll with a dry roller.
  • To allow the painting of straight lines along edges, it is recommended to use an appropriate painters masking tape.
  • Divide larger areas in smaller sections by using grouts as the section border. First time uses should start with one or two tiles to get used to the spreading rate.
  • Apply a single, uniform layer to the surface. Roll cross-wise if required.
  • Finish all sections in the same direction.
  • Avoid rolling back into a finished sections.
How to apply Stellmann Non-Slip

6. Curing and Maintenance

  • Stellmann Non-Slip cures in 12 hours for light foot traffic.
  • Full chemical cure: 3 to 5 days.
  • Maintain the surface conform our Maintenance Guide to get most out of your Stellmann Non-Slip finish.